Skip to content

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf

60 excerpts.

Issue

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 1 · Applies to: 452

01 09 2003 Replaces 00 00 0000 page 1 Remedial measures in the event of water penetration, model 452 Contents 0. Preconditions

page 03 0.1. Definition of a leak 0.2. Rain test on retailer's premises 1. Water penetrates through door's inner liner, front seal – water penetrates at mirror mounting

page 04ff 1.1. Fit mirror mounting 1.2. Adjust mirror mounting 1.3. Mirror mounting cover 1.4. Trim mirror mounting 1.5. Check drainage holes in duct seal 2. Water penetrates via centre of door inner liner - drips running down window from join between roof peak / side spar page 08ff 2.1. Optimise seal fitting 2.2.Optimise side window adjustment / inward adjustment of side door 2.3. Enlarge the drainage hole on the roof peak seal 2.4. Rework roof peak seal 2.5. Reinforce roof peak seal 2.6. Reinforce side spar seal 2.7. Fix seal 3. Water penetrates through rear inner door liner - drips running down rear window

page 21ff 3.1. Reposition side window 3.2 Reinforce rear side spar seal 3.3. Check drainage holes on duct seal

Issue

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 2 · Applies to: 452

01 09 2003 Replaces 00 00 0000 page 2 Remedial measures in the event of water penetration, model 452 Contents 4. Water penetrates at B-pillar:

page 26ff 4.1. Water penetrates through trough/blowpipe/canopy seal, page 26ff 4.1.1. Position blowpipe in door seal trough 4.1.2. Position door seal/trough 4.1.3. Rework canopy seal 4.2. Water penetrates through side spar, rear / head pad page 37ff 4.2.1. Fit a partition. 5. Water penetrates floor area page 39ff 5.1. Leaking roof peak seal 5.1.1. Water penetrates lower sill area 5.2. Leaking floor area/trunk

page 41ff 5.2.1. Rework seal seams at the front 5.2.2. Rework seal seams at the rear 6. Material and tool list

page 45 7. Agreed standards

page 45 8. Allocation of the Service Packages and Work Positions page 46

Issue

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 3 · Applies to: 452

01 09 2003 Replaces 00 00 0000 page 3 Remedial measures in the event of water penetration, model 452 0.1 Definition of a leak: Leaks are points at which water penetrates into the interior of the vehicle and is not fed out via one or more design features without leaving damage to the interior. Example 1: slight drips running down the window which through the dainage openings which are directed out via the drainage holes in the interior door duct seal in the door's wet area do not accord with the definition of a leak, but rather with the state of the art. Example 2: heavy drips of water which run over the door liner conform to the definition of a leak. 0.2 Rain test on the retailer's premises:

Before starting any sealing measure a rain test is carried out to verify the customer complaint. The test is carried out either with a - hosepipe (min. 1/2") with rain attachment or a - watering can (max. 10 ltr.) with rain attachment. After any repair is completed the rain test is repeated to check the effectiveness of the sealing measure. One person sits inside the vehicle during the rain test to check for any water penetration. The 'rain' is applied to the vehicle from a height of approx. 25-30 cm. Rain is applied to each of the 4 corners of the soft top for min. 1 min. To test the bulkhead/floor area for watertightness the right and left A-pillar liners are removed while rain is applied to the whole of the windscreen for at least 2 min. 0. Preconditions

Issue

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 4 · Applies to: 452

01 09 2003 Replaces 00 00 0000 page 4 Remedial measures in the event of water penetration, model 452 Defect figure 1. Water penetrating through door's inner liner/speaker and mirror mounting Note: Drips which reach the inside of the vehicle via the inner liner must

be reduced in volume to ensure that they are able to exit via the duct seal.

Issue

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 5 · Applies to: 452

01 09 2003 Replaces 00 00 0000 page 5 Remedial measures in the event of water penetration, model 452 Measure 1.1. Check the mirror mounting seal fitting and optimise if necessary: •Slacken the inside of the mirror mounting and reposition the seal. Seal fitting OK. Measure 1.2. Optimise mirror mounting fitting: •Slacken the mirror mounting screw fastener and tilt the mirror back slightly so that the door does not compress the roof peak seal when closed. This ensures optimum tightness at the transition from the mirror to the roof peak seal. Contact in "z" and "x" Rotate to the rear

Issue

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 6 · Applies to: 452

01 09 2003 Replaces 00 00 0000 page 6 Remedial measures in the event of water penetration, model 452 Measure 1.3. Check inside of mirror mounting cover: • The butyl seal seam must be replaced when dismantling the inner mirror liner. • Seal the screws (2x) additionally with thread of butyl and an adhesive (spare part no. 001777V001000000). OK not OK

Issue

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 7 · Applies to: 452

01 09 2003 Replaces 00 00 0000 page 7 Remedial measures in the event of water penetration, model 452 OK Thickening Measure 1.5. Check the drainage holes in the duct seal: the water can no longer run through the inner duct seal of the side window. • Check the drainage holes in the front and rear duct seals. • The lip must not close the duct seal channel. Measure 1.4. Adjust mirror mounting seal: IMPORTANT: if the mirror mounting seal is raised by the repositioning of the side mirror it is necessary to address this problem. (See figures)

Issue

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 8 · Applies to: 452

01 09 2003 Replaces 00 00 0000 page 8 Remedial measures in the event of water penetration, model 452 Defect figure 2. Water penetrates through centre of door liner - drips coming down the window from the joint between the roof peak/side spar Note: Drips running down the window and into the vehicle interior via the inner liner must

be reduced in volume to ensure that they are able to drain out through the duct seal. Drips on window

Issue

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 9 · Applies to: 452

01 09 2003 Replaces 00 00 0000 page 9 Remedial measures in the event of water penetration, model 452 Measure 2.1. Optimise the fitting of the seal: • Slacken the roof peak seal, push the weatherstrips together by hand and fit according to the figures. • Once the roof peak seal is removed from the body, check the sealer application in the seal and fill up if necessary. If there is sufficient sealer, it will adhere to the body flange. (See page 36) The seals sit flush side by side, Width of join approx. 1 - 1.5mm Seals in contact with one another and compressing Not OK Not OK OK OK

Issue

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 10 · Applies to: 452

01 09 2003 Replaces 00 00 0000 page 10 Remedial measures in the event of water penetration, model 452 Measure 2.1. • Slacken the roof peak seal, push the weatherstrips together by hand and fit according to the figures. Not OK Not OK OK Roof peak seal is not in contact with the body shell Note: There must be no gaps between the seal and the the body shell at the radius. Figure OK

Issue

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 11 · Applies to: 452

01 09 2003 Replaces 00 00 0000 page 11 Remedial measures in the event of water penetration, model 452 Window is not in contact "in Z" axis Measure 2.2. Optimise side window position: •Optimise side window position in Z and X axes until contact is ensured as shown in figure. Pull the lowering window max. 1.5 mm in the "Z" axis out of the retaining clip. If the adjustment is not sufficient, adjust the door on the hinge in the "Z" axis. The striker should also be adjusted to the door position. Not OK OK Figures Window adjustment screws Window in contact in "Z" axis z y x Standard: The side window must not compress the seals when the door is closed. Rear Front Readjust window stop Mark position

Issue

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 12 · Applies to: 452

01 09 2003 Replaces 00 00 0000 page 12 Remedial measures in the event of water penetration, model 452 Measure 2.2. Inward adjustment of side door: •Optimise side window position in the "Y" axis until the side window is in contact with the side spar. z y x Standard: The side window must not compress the seals when the door is closed. Note: The following measures must be carried out to adjust the position of the side door: •Remove headlamp cover •Slacken fastening screws on the CBS •Remove aerial •Remove door panel •Mark position of side door (x,y,z) •Slacken door screws nos. 1,2 and 4, then carefully slacken screw no. 3. •Rotate side door inwards by approx. 1-1.5mm in the y axis using screw no. 3. •Tighten screws once more to tightening torque M =34Nm+/- 4. Screw no.1 Screw no. 4

Issue

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 13 · Applies to: 452

01 09 2003 Replaces 00 00 0000 page 13 Remedial measures in the event of water penetration, model 452 Measure 2.3. Enlarge the roof peak seal drainage hole: •Enlargement of the drainage hole Enlarge the hole in the seal by approx. 5mm using a scalpel. Attention : do not damage the partition. Partition Before After

Issue

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 14 · Applies to: 452

01 09 2003 Replaces 00 00 0000 page 14 Remedial measures in the event of water penetration, model 452 Measure 2.4. Rework roof peak seal: Abrade the roof peak seal on the sealing surfaces with emery paper (80K). (Length, see figure below) Sealing surface 1 Attention: do not damage the partition! Sealing surface 2

Issue

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 15 · Applies to: 452

01 09 2003 Replaces 00 00 0000 page 15 Remedial measures in the event of water penetration, model 452 Measure 2.4. Rework roof peak seal: •The cellular rubber hose is already fitted during series production and a Festo air line is inserted for stabilisation. •Pull Festo hose into roof peak seal hose insert and fix with Cyberbond 2241 •Festo hose length approx. 20mm.

Issue

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 16 · Applies to: 452

01 09 2003 Replaces 00 00 0000 page 16 Remedial measures in the event of water penetration, model 452 ...and cut out. Measure 2.5. Reinforcement of left and right roof peak seal: •A cellular rubber hose (l=40mm) is inserted to reinforce the roof peak seal •The water drainage channel must be made in the cellular rubber. (See figures) ...mark the exact position of the drainage hole... Insert hose (l=40mm)...

Issue

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 17 · Applies to: 452

01 09 2003 Replaces 00 00 0000 page 17 Remedial measures in the event of water penetration, model 452 ...and spot-glue in place. Reposition hose again Measure 2.5. Reinforcement of left and right roof peak seal: • To ensure that the cellular rubber stays in place, spot-glue it in place with Cyberbond 2241. TIP: Inserting cellular rubber hoses is easier with silicon spray

Issue

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 18 · Applies to: 452

01 09 2003 Replaces 00 00 0000 page 18 Remedial measures in the event of water penetration, model 452 Measure 2.5. Reinforcement of left and right roof peak seal: Measurements of cellular rubber hose •Length = approx.40 mm •Diameter = 13 mm x 3 mm wall thickness •Notch from edge = approx.6 mm •Notch width = approx.8 mm

Issue

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 19 · Applies to: 452

01 09 2003 Replaces 00 00 0000 page 19 Remedial measures in the event of water penetration, model 452 Measure 2.6. Reinforcement of side spar seal: •Insert Festo air line (l= 20mm) into hose insert. •Fix with Cyberbond 2241 Before After

Issue

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 20 · Applies to: 452

01 09 2003 Replaces 00 00 0000 page 20 Remedial measures in the event of water penetration, model 452 Thin and careful application of glue is required Apply pressure to the seal for approx. 2 min Measure 2.7. Fix the side spar seal: •The roof spar seal is glued firmly to the end of the roof spar for a length of 50mm.

Issue

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 21 · Applies to: 452

01 09 2003 Replaces 00 00 0000 page 21 Remedial measures in the event of water penetration, model 452 Defect figure 3. Water penetration via rear inner door liner / drips on window at rear Note: Drips running down the window and into the vehicle interior via the inner liner must be reduced in volume to ensure that they are able to drain out through the duct seal.

Issue

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 22 · Applies to: 452

01 09 2003 Replaces 00 00 0000 page 22 Remedial measures in the event of water penetration, model 452 Measure 3.1. Check the position of the side window and adjust if necessary: Pull the lowering window max. 1.5 mm out of the retaining clip in the "Z" axis. If the gap is too large the entire door must be raised in the "Z" axis. Use the door-side hinge screws to raise the door in the "Z" axis. OK Not OK OK Not OK Gap minimised by window adjustment: ‹ 1mm Gap from window to seal too large After Before Before After

Issue

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 23 · Applies to: 452

01 09 2003 Replaces 00 00 0000 page 23 Remedial measures in the event of water penetration, model 452 Measure 3.2. Reinforcement of side spar seal, rear: •A cellular rubber hose (L=70mm, 13x3mm) is inserted into the rear side spar to stabilise the sealing profile. •Make a drainage channel. (See figures) •Position the cellular rubber hose by spot-gluing with Cyberbond 2241. Take care: the chnnel and the drainage hole in the side spar must line up. TIP: Inserting cellular rubber hoses is easier with silicon spray

Issue

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 24 · Applies to: 452

01 09 2003 Replaces 00 00 0000 page 24 Remedial measures in the event of water penetration, model 452 Length = 70 mm Drainage channel web width = 7 mm Channel notch = 8 mm

Issue

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 25 · Applies to: 452

01 09 2003 Replaces 00 00 0000 page 25 Remedial measures in the event of water penetration, model 452 Measure 3.3. Check the drainage holes in the duct seal: The water cannot drain through the inner duct seal of the side window: Check the drainage holes in the front and rear duct seals. Reposition the seal if necessary. • The lip must not close the duct seal channel.

Issue

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 26 · Applies to: 452

01 09 2003 Replaces 00 00 0000 page 26 Remedial measures in the event of water penetration, model 452 Defect figure 4. Water penetration at B-pillar Preliminary measure: check roof position and adjust if necessary. The joint between the canopy/hard top shell to the roll bar must be 7 mm in the X-axis (tolerance +/- 2mm). If this value lies outsuide the tolerance or if left and right differ significantly, the soft top must be adjusted at the supports (B-pillar). Attention: note the gap/transition between the soft-top and the running rails (parallel, not distorted)! 7 mm (+/-2mm) Running rail side spar Running rail Module carrier

Issue

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 27 · Applies to: 452

01 09 2003 Replaces 00 00 0000 page 27 Remedial measures in the event of water penetration, model 452 Defect figure 4. Water penetration at B-pillar 4.1. Water penetration via trough/ canopy seal blow pipe Canopy seal blow pipe, wasser exiting from canopy trough Water via inner liner

Issue

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 28 · Applies to: 452

01 09 2003 Replaces 00 00 0000 page 28 Remedial measures in the event of water penetration, model 452 Defect figure 4. Water penetration at B-pillar 4.1. Water penetration via trough/ canopy seal blow pipe Measure 4.1.1. Positioning the blow pipe in the door seal trough: • The blow pipe must be positioned above the trough of the door seal. Photo from beneath (Example -hard top seal) Not OK OK Blow pipe in door seal trough

Issue

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 29 · Applies to: 452

01 09 2003 Replaces 00 00 0000 page 29 Remedial measures in the event of water penetration, model 452 Defect figure 4. Water penetration at B-pillar 4.1. Water penetration via trough/ canopy seal blow pipe Measure 4.1.2. Position the door seal/trough: •The door seal trough must be in contact with the side spar. Not OK OK

Issue

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 30 · Applies to: 452

01 09 2003 Replaces 00 00 0000 page 30 Remedial measures in the event of water penetration, model 452 Defect figure 4. Water penetration at B-pillar Measure 4.1.3. Rework the canopy seal: •If the blow pipe (canopy) collides with the door seal trough when the top is down, the position of the door seal must be changed. (See figure) •If the canopy seal collides with the door seal at the side, the canopy seal must be trimmed. (Overleaf). Collision Collision Not OK Blow pipe in trough No collision OK

Issue

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 31 · Applies to: 452

01 09 2003 Replaces 00 00 0000 page 31 Remedial measures in the event of water penetration, model 452 Defect figure 4. Water penetration, B-pillar Measure 4.1.3. Rework canopy seal Trim canopy seal trough (only if collision with door seal and contact not OK) Emery door seal in this area. (emery paper grade 80) Trim by 1-2mm

Issue

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 32 · Applies to: 452

01 09 2003 Replaces 00 00 0000 page 32 Remedial measures in the event of water penetration, model 452 •The canopy seal is fastened to the soft top with Cyberbond 2241 and sealed. •Apply glue to the radius (until the radius run-off) and approx. 10mm before the inner drainage hole. Defect figure 4. Water penetration, B-pillar Measure 4.1.3. Rework canopy seal

Apply pressure to the seal for approx. 20 sec Remove any glue which seeps out Apply glue with care. Area of glue application (mark) Position of inner drainage hole

Issue

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 33 · Applies to: 452

01 09 2003 Replaces 00 00 0000 page 33 Remedial measures in the event of water penetration, model 452 Measure 4.1.3. Rework canopy seal (if not yet carried out) Not OK OK Not OK OK

Issue

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 34 · Applies to: 452

01 09 2003 Replaces 00 00 0000 page 34 Remedial measures in the event of water penetration, model 452 Defect figure 4. Water penetration, B-pillar Measure 4.1.3. Rework canopy seal To prevent drips forming below the blow pipe, treat inside and underside of the blow pipes with grease, item no. 0017777V001000000. Note: Water drops or moisture on the inside of the roof module carrier do not indicate a roof leak. When the soft top is opened after rain, water collected there can drip over the edge of the canopy seal.

Issue

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 35 · Applies to: 452

01 09 2003 Replaces 00 00 0000 page 35 Remedial measures in the event of water penetration, model 452 Sealant application, old Sealant application, current Permitted area below the moulding for sealant exit Defect figure 4. Water penetration, B-pillar Measure 4.1.3. Rework canopy seal
•Remove canopy seal and replace sealant application ( flexible window sealant) according to the figure. Not OK OK

Issue

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 36 · Applies to: 452

01 09 2003 Replaces 00 00 0000 page 36 Remedial measures in the event of water penetration, model 452 Diameter of sealant application O = 7mm Defect figure 4. Water penetration, B-pillar Measure 4.1.3. Rework sealant application on canopy seal:

Issue

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 37 · Applies to: 452

01 09 2003 Replaces 00 00 0000 page 37 Remedial measures in the event of water penetration, model 452 Defect figure 4. Water penetration, B-pillar 4.2. Water penetration via rear side spar / head pad Water penetration between side spar and head pad

Issue

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 38 · Applies to: 452

01 09 2003 Replaces 00 00 0000 page 38 Remedial measures in the event of water penetration, model 452 Notch for screw arbor in rear side spar Glue a partition into rear side spar (self-adhesive foam tape in pack 0017777V001000000) Measure 4.2.1 Fitting a partition Length = 85mm Height = 9mm Depth = 4mm Length of groove = 15mm Distance of groove = 10mm

Issue

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 39 · Applies to: 452

01 09 2003 Replaces 00 00 0000 page 39 Remedial measures in the event of water penetration, model 452 Defect figure 5. Water penetration in the floor area 5.1. Leak in the roof peak seal Water running over the sill into the floor area because the water changes sides in the seal's weather strip.

Issue

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 40 · Applies to: 452

01 09 2003 Replaces 00 00 0000 page 40 Remedial measures in the event of water penetration, model 452 Defect figure 5. Water in the floor area 5.1. Leak in roof peak seal Measure 5.1.1. Water penetration into lower sill area •Unfasten A-pillar seal up to the sill and reseal the weather-strip groove (flexible window sealant) (Push weather-strip together again before fitting). Sealant bead approx. 3mm diameter Flexible sealant

Issue

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 41 · Applies to: 452

01 09 2003 Replaces 00 00 0000 page 41 Remedial measures in the event of water penetration, model 452 Defect figure 5 Water penetration in the floor area 5.2. Leak in the body shell Measure 5.2.1. Rework the seal seams in the front area •Check seams and rework if necessary (use standard body sealant). Fastening screws - seal Side wall area below FLA right/left

Issue

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 42 · Applies to: 452

01 09 2003 Replaces 00 00 0000 page 42 Remedial measures in the event of water penetration, model 452 Defect figure 5 Water penetration in the floor area 5.2. Leak in the body shell Measure 5.2.1. •Check seams and rework if necessary (standard body sealant). Rear power brake area

Issue

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 43 · Applies to: 452

01 09 2003 Replaces 00 00 0000 page 43 Remedial measures in the event of water penetration, model 452 Defect figure 5. Water penetration in the floor area 5.2. Leak in the body shell Measure 5.2.1. •Check seams and rework if necessary (standard body sealant). •The seal seams can be subjected to rain test with a watering can when vehicle is dismantled. Area in front of right bulkhead

Issue

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 44 · Applies to: 452

01 09 2003 Replaces 00 00 0000 page 44 Remedial measures in the event of water penetration, model 452 Defect figure 5. Water penetration in the floor area/trunk 5.2. Leak in the body shell Measure 5.2.2. Rework seal seams in the rear area: •Check seams and rework if necessary (standard body sealant). •The seal seams can be subjected to rain test with a watering can when vehicle is dismantled. Unused screw holes must be covered with the adhesive. Seal seams

Issue

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 45 · Applies to: 452

01 09 2003 Replaces 00 00 0000 page 45 Remedial measures in the event of water penetration, model 452 6. Material and tool list Material: Repair kit, soft top seals Spare parts package number 0017777V001000000 Tool: •Nail shears • Standard emery paper K.80 7. Agreed standards smart roadster: •ERM service package 11010107 smart roadster-coupé: •ERM service package 11010108

Issue

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 46 · Applies to: 452

01 09 2003 Replaces 00 00 0000 page 46 Remedial measures in the event of water penetration, model 452 8. Allocation of the Service Packages and Work positions: Rain test before the remedial measure: Service Package in smart DMS 8.0: 01030153E49 Work Position in DaimlerChrysler ASRA: 02 4007 0 Rain test after the remedial measure: Service Package in smart DMS 8.0: 01030159E49 Work Position in DaimlerChrysler ASRA: 02 4019 0 Defect figure 1. with measures 1.1. to 1.5.: Service Package in smart DMS 8.0: 01030154M15 Work Position in DaimlerChrysler ASRA: 02 4008 0 Defect figures 2. and 3. with measures 2.1. to 3.3.: Service Package in smart DMS 8.0: 01030155M15 Work Position in DaimlerChrysler ASRA: 02 4015 0 Defect figure 4. with measures 4.1. and 4.2.: Service Package in smart DMS 8.0: 01030156M15 Work Position in DaimlerChrysler ASRA: 02 4016 0 Defect figure 5. with measures 5.1.1.: Service Package in smart DMS 8.0: 01030158M15 Work Position in DaimlerChrysler ASRA: 02 4018 0 Defect figure 5. with measures 5.2.1. and 5.2.2.: Service Package in smart DMS 8.0: 01030157M15 Work Position in DaimlerChrysler ASRA: 02 4017 0

smart gmbh 09.06.2005 page 1/14

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 47 · Applies to: 452

Remedial measures, seals, model R/C 452 Supplementary information

smart gmbh 09.06.2005 page 2/14

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 48 · Applies to: 452

Contents • General information • Assigning parts to year of manufacture • Ideal sequence of remedial steps • Tips and tricks for rapid achievement of objectives Remedial measures, seals, model R/C 452 Supplementary information

smart gmbh 09.06.2005 page 3/14

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 49 · Applies to: 452

  1. General information
  2. Deciding which part to use for different model years For model year 2003 vehicles, use parts from group "A" For model year 2004 vehicles, use parts from group "A" For model year 2005 vehicles, use parts from group "B" Never mix parts from different groups. These criteria were agreed by smart gmbh based on a wide range of measured variables and form the basis for the warranty appraisal. Important notes: Fitting sealing systems in contravention of these criteria will invalidate any warranty/goodwill claim for the requisite work. Due to parts shortages for model year 2003 and 2004 vehicles, smart gmbh has converted a certain number of vehicles to the model year 2005 sealing system. Converted vehicles (2005 status) can be recognized by the features described on page 7 ! Remedial measures, seals, model R/C 452 Supplementary information

smart gmbh 09.06.2005 page 4/14

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 50 · Applies to: 452

  1. Definition of leaks / drips Leaks are defined as water entering the vehicle interior which is not directed out again by design measures without causing residual damage to the interior. Example 1: Slight drips on the window which are directed back outwards via drainage holes in the inner door well seal into the wet area of the doors are not considered as leaks according to the definition, but rather as the state of the art. They are described as such in the owner’s manual. Example 2: Heavy drips on the window which run over the door cladding are considered as leaks within the terms of the definition. Remedial measures, seals, model R/C 452 Supplementary information

smart gmbh 09.06.2005 page 5/14

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 51 · Applies to: 452

  1. Assigning parts to years of manufacture Assigning the sealing package "A" to model year 2003 and 2004 vehicles •Roof peak seal 0017060V002000000 •Side strut seal, right 0009358V006000000 / Hardtop seal, right 0009360V006000000 •Side strut seal, left 0009357V006000000 / Hardtop seal, left 0009359V006000000 •Door seal, right 0009309V008000000 •Door seal, left 09308V008000000 •Window guide seal, front right 0011234V008000000 •Window guide seal, front left 0009789V008000000 •Exterior mirror, manual, right 0009725V007C22A00 LHD / 0011326V007C22A00 RHD •Exterior mirror, manual, left 0009724V007C22A00 LHD / 0011315V007C22A00 RHD •Exterior mirror, electric, right 0009819V006C22A00 LHD / 0012958V005C22A00 RHD •Exterior mirror, electric, left 0009818V006C22A00 LHD / 0012932V005C22A00 RHD Remedial measures, seals, model R/C 452 Supplementary information

smart gmbh 09.06.2005 page 6/14

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 52 · Applies to: 452

Assigning sealing package "B" to model year 2005 vehicles •Roof hard top seal 0017060V004000000 •Side strut seal, right 0009358V007000000 / Hard top seal, right 0009360V007000000 •Side strut seal, left 0009357V007000000 / Hard top seal, left 0009359V007000000 •Door seal, right 0009309V009000000 •Door seal, left 0009308V009000000 •Window channel seal, front right 0011234V010000000 •Window channel seal, front left 0009789V010000000 •Exterior mirror, manual, right 0009725V008C22A00 LHD / 0011326V008C22A00 RHD •Exterior mirror, manual, left 0009724V008C22A00 LHD / 0011315V008C22A00 RHD •Exterior mirror, electric, right 0009819V007C22A00 LHD / 0012958V006C22A00 RHD •Exterior mirror, electric, left 0009818V007C22A00 LHD / 0012932V006C22A00 RHD Remedial measures, seals, model R/C 452 Supplementary information

smart gmbh 09.06.2005 page 7/14

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 53 · Applies to: 452

Ways of differentiating between the two sealing systems Seals for model year 2005 can be recognized by the flocking on the roof peak seal and door seal. The model year 2005 exterior mirror can be recognized by its triangular mirror cover (no screw fastening, presence of rubber lip). Remedial measures, seals, model R/C 452 Supplementary information

smart gmbh 09.06.2005 page 8/14

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 54 · Applies to: 452

  1. Disassembly of CBS parts
  2. CBS front
  3. CBS rear
  4. Door panel right/left
  5. Interior/carpet
  6. Sealing of body seams
  7. Description, see Info Letter 02.04.2004
  8. Assembly of seals
  9. Description, see Info Letter 25.08.2003 Sealant
  10. Ideal sequence of remedial steps Remedial measures, seals, model R/C 452 Supplementary information

smart gmbh 09.06.2005 page 9/14

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 55 · Applies to: 452

  1. Assembly and positioning of side struts
  2. Description, see Info Letter 25.08.2003
  3. Positioning of side window with respect to door frame
  4. Description, see Info Letter 25.08.2003 Remedial measures, seals, model R/C 452 Supplementary information

smart gmbh 09.06.2005 page 10/14

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 56 · Applies to: 452

  1. Fitting CBS parts
  2. Carry out rain test
  3. Description, see Info Letter 02.04.2004
  4. Assembly/positioning of the exterior mirror
  5. Description, see Info Letter 02.04.2004 Remedial measures, seals, model R/C 452 Supplementary information

smart gmbh 09.06.2005 page 11/14

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 57 · Applies to: 452

  1. Carry out reworking as required
  2. Interior fittings / checking vehicle functions
  3. Warranty / goodwill claim
    • documentation Remedial measures, seals, model R/C 452 Supplementary information

smart gmbh 09.06.2005 page 12/14

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 58 · Applies to: 452

  1. Basic adjustments on the door frame
  2. Adjust the roof peak seal (DSP) to fit the body
  3. Adjust the side struts to fit the roof frame and the DSP Note Use the special tool "soft top template" (part number Q001 9576 V001000000/ window adapter W452 589032300) to adjust the soft top (base carrier) and the A/B pillars to a defined position with respect to one another. This soft top template is used to fasten the individual parts to the body and is also used to fit the side window / side door to the door frame. Fitting instructions are given in WIS work package AR 77.30-P-1010 RR. The special tool "Soft top template Q0019576V001000000" is subject to guaranteed availability. You can order the template via the standard ordering procedure.
  4. Tips and tricks for rapid achievement of objectives Remedial measures, seals, model R/C 452 Supplementary information

smart gmbh 09.06.2005 page 13/14

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 59 · Applies to: 452

  1. Checking the position of the side window with respect to the side strut For this purpose, the side strut is inserted into the body and the soft top closed. The side door is examined with respect to the fit of the side window and the seal. In this case the side window must be in contact with the entire surface of the sealing profile. (see 2. Ideal sequence of remedial steps, no. 5) If the side window needs re-adjusting, use the soft top template (or additional side window adapter) to adjust the side window. Fitting instructions are given in WIS work package AR 77.30-P-1010 RR.
  2. Optimizing the side window position (contact with window opening mechanism) The side window needs to be fixed to the window opening mechanism to prevent it from dropping after a certain amount of time in use. For this purpose, O-rings, part number 0021709V001000000, are attached to the window opening mechanism sliders. Fitting the O-rings and/or replacing the sliders is described in the WIS work package AR 72.10-P- 1805 RR. Remedial measures, seals, model R/C 452 Supplementary information

smart gmbh 09.06.2005 page 14/14

2003-2006 smart Roadster (452) - Water Penetration Remedial Measures Guide.pdf · p. 60 · Applies to: 452

• Transition; side window to exterior mirror There must be a seamless transition to the side window when fitting the exterior mirror. The exterior mirror is therefore adjusted to the correct position when the side window is closed (see 2. Ideal sequence of remedial steps, no. 6). Take particular care that the window channel seal is fitted correctly at the front. Particularly with YOM 2005 it must fit snugly to the mirror. 5. Basic adjustment of soft top and positioning of seals After using the soft top template the roof cap (rear soft top seal) should be adjusted to the correct position with respect to the anti-roll bar. The contact pressure can be checked using, e.g. a check card. The check card should be able to move between the body and the roof cap but with a slight resistance. This will minimize the amount of water penetrating and ensure that it is more easily drained away by the water management design measures. To ensure the correct positioning of the drainage pipe on the roof cap, the inside and outside surfaces are greased with a rubber-based grease (Krytox grease). The upper section of the door seal is also treated with the same grease. Remedial measures, seals, model R/C 452 Supplementary information